750window.comPublished by Factory Direct Windows
Home›Guides›Process
Process · Guides for Phoenix homeowners

How to measure a window for replacement (and why we do it for free)

Measure width in three places (top, middle, bottom) and height in three places (left, centre, right) from inside the existing frame, and use the smallest of each. Check the frame is square by measuring both diagonals. For a price you don't need any of this — text us a photo and we measure on site before ordering, free.

Last checked October 2026 · Published by Factory Direct Windows · Prices are the published $750-per-window rate on this site; competitor figures are third-party published ranges with sources.

The five-minute method

  1. Width, three times. Inside the frame (jamb to jamb), at the top, the middle and the bottom. Write down all three.
  2. Height, three times. Sill to head, at the left, the centre and the right.
  3. Use the smallest width and the smallest height. Openings are rarely perfectly square; the new window has to fit the tightest point.
  4. Check square. Measure corner to corner both ways. If the diagonals differ by more than about ¼", say so — a retrofit frame can shim to it, but the installer needs to know.
  5. Depth. From the inside stop to the outside of the frame — a retrofit frame needs roughly 3" of depth; most Valley stucco openings have it.

A worked example

A typical 36×48 bedroom window measures like this
MeasurementTop / LeftMiddle / CentreBottom / RightUse
Width35 ⅞"35 ¾"35 ⅞"35 ¾"
Height47 ½"47 ⅝"47 ⅝"47 ½"
Diagonals59 ¾"59 ⅝"Square within ⅛" — fine

Retrofit vs full-frame changes what you measure

Most Phoenix stucco homes get a retrofit (insert) window: the new frame sits inside the existing frame's opening, so you measure the inside of the old frame, as above. A full-frame replacement removes the old frame to the rough opening — measurements are taken from the framing, after demolition, and it's a different (bigger) job. If you're not sure which you have, this guide sorts it out; our $750 price is the retrofit.

Mistakes that cost money

  • Measuring the glass instead of the frame opening.
  • Measuring once, in the middle, and ordering to it.
  • Rounding up. Windows are made to the eighth of an inch; a window ⅛" too big does not go in.
  • Forgetting that one window with two sashes is one window, and a bay is usually three.
  • Ordering online from your own numbers with no one to call when it doesn't fit.

Why we measure for free

Because the measure is where the price gets confirmed. Text photos, get the $750-per-window number in minutes, and we measure in person before anything is ordered — if a window is oversized, tempered by code, or a specialty shape, you hear it then. Nobody sits at your kitchen table for three hours, and you never order a window to a tape measure.

Whatever you decide, here's the number: $750 per window, installed, sales tax included, lifetime warranty — anywhere in metro Phoenix. See what's in it, or find your city.

Questions

Asked before the first text.

Do I need to measure my windows to get a quote?

No. Count them and text three photos; the $750 average covers standard sizes and we measure on site before ordering.

What's the standard window size?

There isn't one — but 36×48, 48×48, 60×48 and 72×48 sliders cover most Valley bedrooms and living rooms. The $750 price applies across standard sizes.

Can I measure a window for a screen the same way?

Screens are measured to the screen channel, not the frame opening; width and height of the existing screen frame is enough.

Ready when you are

Seven-fifty. Say it with us.

Count your windows, text us a photo, or call. You'll have the whole number in minutes — and nobody will sit at your kitchen table for three hours.

7 AM – 7 PM, seven days a week · Chandler, Gilbert, Mesa, Tempe, Scottsdale, Phoenix, Peoria, Glendale, Surprise, Goodyear and the rest of the Valley.

Text a photoCall 602-703-0131